')){kind=link}
Package Includes:
100 pcs led strip clips
100 pcs screws
These led clip are mounting brackets clips which suitable for WATERPROOF LED light strip , to fix by one screw for each clip, don’t affect the lamp brightness.
Ideal for Waterproof Strip Width 10mm
The bracket has 11mm hollow distance and 3mm hollow height. It is ideal fixture to mount the SMD5050 LED waterproof strip light within 10mm width.
Ultra-thin appearance design
This mounting brackets has an ultra-thin appearance design, which made it can hold the lighting effect of the strip light completely and no damage on brightness.
Upgraded installation process
The upgraded installation process made it easy to fix by one screw for each clip. You can take it down from the other end side freely when you want to replace or maintain the LED strip lights
Specifications:
Hollow distance: 11mm
Hollow height(Max.): 3mm
Material: plastic nylon 66, UL 94V-0
screw: 3*10mm
Use and installation:
1.When you receive the LED strip clips, Please check out whether the sizes of the clips are compatible with your LED light strip or not.
2.Shut down the power before installing the clips.
3.Rip off the 3M paper on the adhesive tape behind the strip light, then choose an proper place for installing the strip light.
4.Plan the mounting holes and make the markings, suggested using 3 – 6 pieces clips within 1 meter long strip lights.
5.Due to the very small clips, suggested firstly putting screws through the clips and then fixed the screw in the marked mounting holes(Pls be careful not to tighten it completely).
6.Adjust these led clips so that they can coincide with the strip surface, and then continue to tighten the screw until the clip completely clamp light strip.
7.After complete the installation, please check whether all are in place.
Product Features
- The led clip is suitable for 10 mm waterproof led strip lights with Silicone surface
- Fix by one screw for 4pin 3pin 2pin 10 mm PCB board(No need stripping glue coating on PCB). Compatible with both 12v and 24v 5050 rgb led strip, addressable led light strip ws2813(upgraded ws2812b led strip)
- These led light clips were designed for screwing into wood materials such as cabinet, Wardrobe,bookcase. Ultra-thin appearance design, Safe and secure to hold led strip, no damage on brightness
- 100pcs of mounting bracket clips and 100pcs screws included, easy to fix by one screw for each clip, take down the LED light strip from the other end freely when replace or maintain it
- If your led strips are 10mm NON-WATERPROOF lights, pls refer to this item (ASIN:B017FYRKPQ). If for 8mm waterproof 3528 2835 3014 5630 led light strip, pls refer to this item (ASIN:B01GM805YE)
Related Posts
Ashialight LED 12 volt ba15d Bulb-35 watt DC Bayonet Base Halogen Light Bulb,Soft White,Repalces JD Type T3/T4 Bulbs (Pack of 2) Bayonet Base LED Halogen Replacement […] Posted in LED DC Bulbs
STANLEY Handheld Flashlight with Lanyard, 3 Modes Ultra Bright LED Torch Aluminum-crafted Waterproof IPX4, 3AAA Alkaline Battery Included
Specifications: - Bulb: CREE LED - […] Posted in LED Flashlights
Lumitec Caprera2 101102, LED Flood Light, Bracket Mount, White Housing, White Dimming and Blue Dimming Lumitec's Caprera2 LED flood lights is […] Posted in LED DC Bulbs
These bracket clips work just fine on my LEDMO 5630 LED strips. I used this with the LEDMO 5630 LED strips. My LEDs were waterproof, so they were a little thicker. But these mounting clips still worked fine. I like how they only had one hole for mounting, since I mounted my LEDs vertically, on the inside of a wood cabinet face. See photos. They are just springy enough to allow some give, but still keep the LED strip secure. You might as well not even use the built-in double-sided tape that comes on the back of the LEDs, as it will not stick to wood…
Too flexible to apply any hold-down force, and weak screw heads snapped off These didn’t work well for my project. Part of the fault was mine: I didn’t realize that the light strip tape that I ordered was literally paper-thin, so these clips had no ability to hold the tape flat. I had to turn it around so the tongue on the opposite end from the clip (the right side of the photo of the product) was holding the tape down.In fact, in the third photo on the listing, showing a top view of two clips “holding down” a bit of light tape, now that I’m looking…
Comments are disabled for this post.