){kind=link}
10m 5050 LED strip
Light source: SMD 5050
Emitting Color: RGB
FPCB color: White
LED quantity: 60LEDs/M
Protection Rate: IP65 Waterproof
Working Voltage: 24V DC
Max Working Current: 5A
Max Output power: 120W
Beam angle: 120 °
Working temperature: -20℃ to 60℃
Size: L1000cm (10M) x W1.0cm x T0.25cm
Net weight: 410g
Life span: >50000 hours
44-Key IR Remote Controller
16 colors
5 light patterns: Static/Flash/Strobe/Fade-change/RGB Smooth-change
16 classes Static Mode Dim Control
Input / Output Voltage: 24V
Max load current: 2A each color max (6A max in total)
Power: 144W max
Working temperature: -20℃ to 60℃
24V 5A power supply
Input Voltage: 100~240V AC
Output Voltage: 24V DC
Output Current: 5A max
Safety Compliance: CCC /CE
Working Temperature: -20~60℃
Ambient Humidity: 0~95% Non-Condensation
Kindly note
1) It can be cut off between every 6LEDs without damaging the rest strip. You can configure it freely.
2) Please spread all the strip from the tape before use. Otherwise, the strip will overheat in several minutes.
Package included
1 x 10 meters LED strip light
1x 24V 5A Power supply
1x 44key IR remote controller
Product Features
- 【All in one kit, plug and play】The kit contains 10m 24V RGB LED strip & controller & 24V 5A adapter. It is much brighter than old 12V version. Just connect them together and they will work very well. So easy!
- 【Double fixation】It comes with both self-adhesive tape on back and some clips & screws.10m led strip is so weight that sometimes the tape alone cannot fix it firmly, then you can reinforce it with the clips.
- 【Cut and bend freely】The light is flexible and can be cut off between every 6LEDs. You can configure the length and shape you want. It is covered with clear silicone coating, which protects it well from water and dust and makes it easy to clean.
- 【Amazing color change】You can set 20 static colors, adjust 16 classes brightness, select 5 light patterns (static/flash/strobe /fade-change/RGB smooth-change) and DIY the colors by yourself.
- 【More convenient but less cost】 10m continuous length LED strip is equivalent to 2pcs 5m led strip and 1pc amplifier. But if choose 10m LED strip, you will save much money, labor and time.
Related Posts
20W 12inch LED Flush Mount Ceiling Light Round LED Ceiling Lamp 3000K Warm White Lighting Kitchen Bathroom Hallway Stairwell Power: 20W Size: 30*30*5cm Light […] Posted in LED Lighting
LED Light Bar Nilight 2PCS 4 Inch 60W Spot & Flood Combo Driving Light Waterproof Led Work Light Triple Rows Off-road Truck Car ATV SUV Jeep Cabin Boat, 2 Years Warranty Specification: LED Power:60W (20 x 3W […] Posted in LED DC Bulbs
27W Round LED Work Light Lamp Off Road High Power ATV Jeep 4×4 Tractor 30 Degree Spot Light Specifications: Power: 27W Operating […] Posted in LED Lighting
Not exactly as advertised. . Yes, it is 10 meters long, but in one 22 Ft piece and a second 10 Ft piece. Both pieces were made from shorter pieces soldered together at the cut points. The long piece is intermittent in the middle – often only 1/2 of it works – you have to twist it around to make it work. Power consumption was about 3.7 amps for all 32 feet in two pieces (22ft and 10ft), with about 2-3 volts drop on the longer piece. LEDs are quite bright, and it gets warm after a while. I…
I purchased the warm white led strip. I measured the actual length I received, it was 10M as declared. As per the description these are actually made up of segments of 6 LEDs and each segment has little copper patches at each end to solder wires on to. What I don’t think they tell you is that the 10M strip is actually made up of lots of smaller strips soldered together. Each section is 60 LEDs (I estimate about 500mm long) and these sections are soldered together to form the length. The strip…
Comments are disabled for this post.