){kind=link}
Parameter
Model: 5m/roll WS2812B dream color LED strip
Light source: SMD 5050 RGB
Wave length (NM): R/650nm; G/520nm; B/460nm
FPCB color: Black
Protection Rate: IP67 Waterproof (Can be used outdoor but not underwater)
LED quantity: 60LEDs/m, 5m 300 LEDs in total
IC Model: Built-in WS2812B IC, one IC controls one LEDs
Working Voltage: 5V DC
Max Working Current: 18A
Power: 18W/M, 90W/Roll
RGB Sequence: G/R/B
Beam angle: 120 degree
Working temperature: -20 to 60 Degrees Celsius
Size: L500cm (5M) x W1.2cm x T0.25cm
Net weight: 250g
Life span: >50000 hours
Kindly note: The LED strip comes without power supply and controller.
Kindly note
1) You must use a 5V DC power supply to power these strips, do not use higher than 6V or you can destroy the entire strip.
2) Led strip is made by 50cm FPCB, so there is a solder point each 50cm on strip. But this minor flaw has no any bad effect on the strip’s performance. In fact, most of the LED strips on the market are manufactured in half-meter lengths.
3) If you want the data sheet of WS2812B, please contact us, we will send it to your email.
Package:
1x 16.4ft 300 pixels WS2812B led strip (Power supply and controller are not included)
Related product links
5V 15A Power supply:
https://www.amazon.com/dp/B01LXN7MN3
SP105E Bluetooth Magic LED Controller:
https://www.amazon.com/dp/B01LW1J10W
SP103E Mini Wireless RF Remote Controller:
https://www.amazon.com/dp/B01HCHHM04
T1000S LED Controller:
https://www.amazon.com/dp/B01M4IX5FF
Product Features
- 256 brightness display and 24-bit color display. Each pixel can have its own color and brightness. You can control them individually and set them to any color or animation you want.
- It can be programmed with Arduino, FastLED library, Raspberry Pi, Fadecandy, T1000S etc. It can also be controlled by SP105E, SP103E, HC008 and other pre-programmed WS2811 controllers.
- Covered with silicone weatherproof sheathing, which protects it very well and makes it easy to clean. It comes with clips and screws and can be installed easily.
- Come with 3pin JST-SM connectors and separated power/ground wires on both ends. Each LED can be cut off without damaging the rest strip. You can shorten, lengthen or bend it freely if you want.
- Used to make led screen, led wall, advertising board and widely applied to hotel, KTV, bars, Outdoor advertising signs, Christmas or wedding party decoration, and so on.
Related Posts
Alkbo® RF mini monochromatic controller 11 key radio frequency DC head with dimming LED monochrome light dimmer FOR LED light strip, LED work light, LED flood light, LED off road light, LED light bar Alkbo is SOLE Alkbo brand seller ! […] Posted in LED DC Bulbs
20 Watt LED Portable Worklight Floodlights w/Telescoping Tripod 1900 Lumens, Set of 3 With 1,900 lumens at 6500K, the LED […] Posted in LED Lighting
Waterproof Warm White LED Light Strip, Premium High Density 3528 – 16.4 Feet, 600 LEDs, 3000K, 164 Lumens per Foot. 12V DC. UL-Listed Our Waterproof High Density Premium […] Posted in LED DC Bulbs
Great product I used these for making a costume. They worked well and seem to be quite durable. There are a few gotchas to working with them though.1. The weatherproofing sleeve is too slick to be hot glued to anything. The glue just falls off as it cools.2. Keep in mind how much power each light can use at most (60ma). As a result, the whole roll of lights at full bright white light can use up to 18A!3. Don’t expect to use the entire roll in a single run as the…
Otherwise it works fine and is bright enough I bought this to use as a makeshift lightpack/adalight behind my monitor. After plugging it in and testing it, only 2 of the leds of the entire strip lit up. I then bypassed a few leds and the rest of the strip worked. It was irritating to have to remove the preinstalled jack and resolder it to a later point so I docked 2 stars off for that. Otherwise it works fine and is bright enough.PRO- works well once you remove dead ledsCON- dead leds really hurt the…
Comments are disabled for this post.