, Soft White (3000K), Bright White (4000K), White Finished, 12-inch, IN-0210-1')){kind=link}
GetInLight IN-2010 Series LED Under Cabinet Lighting Fixture features a temper switch allowing selection of 1 of 3 color levels, Warm White (2700K), Soft White (3000K) & Bright White (4000K). Can be attached to the cabinet with 2 captive mounting screws, which provides a smoother installation.
Construction
- Housing is a slim 1″ profile made of extruded aluminum
- Built in driver, no transformer or adapter required
- Integrated LEDs built in, no need to replace
- 3 position switches allows you to choose full brightness, 50% of full brightness or off
Electrical
- 2 LED arrays are used to create 2700K, 3000K or 4000K color temps
- Produce 300 Lumens light while only using 5-Watt of electricity
- Utilizes high performing LEDs with greater than 90 CRI
- Dimmable to 10% with most standard dimmers
- Lifetime rated for greater than 50,000 hours
Optical System
White polycarbonate diffuser eliminates hot spots creating a pleasantly uniform light distribution
Finish
Matte white
Installations
Plug-in or Hardwire installation
Optional junction box (IN-0501-2) is available for use to create a paddle-switch under cabinetry
Optional linking cord available in 12″ (JC1-12-WH), 24″ (JC1-24-WH), 32″ (JC1-32-WH) and 60″ (JC1-60-WH)
Listing
cETLus listed for dry location
This Kit Includes
(1) LED Under Cabinet Lighting Fixture
(1) 6 ft. cord and plug
(1) 6 in. linking cord
(1) End-to-End connector
(1) Romex connector
(2) Wood screws
(1) Installation instructions
Warranty
5-year limited system warranty standard
We guarantee the quality of all GetInLight products. If this product does not perform properly, please contact us.
Product Features
- Features a Temper Switch Allowing Selection of 1 of 3 color levels, Warm White (2700K), Soft White (3000K) & Bright White (4000K)
- Aluminum Housing with Easy Access Knock-outs and Polycarbonate Diffuser
- Hardwired or Plugged-In installation
- Link up to 20 units to a single power supply
- Dimmable with Most Wall/Box Dimmers, Hi/Low Switch for Non-dimming Applications. Dimmers that have been tested with this fixture: LUTRON-DV-603PG, LUTRON-DVCL-153P, LUTRON-DV-600P, LUTRON-DVLV-600P, LUTRON MACL-153M, LEVITON-6611-P0W
Related Posts
Lightahead® 200 LED Solar Christmas Lights 22 meter (72 feet) Outdoor Garden Solar Powered String Lights Waterproof (WARM WHITE)
Unmatched Quality from Lightahead® […] Posted in Solar Lighting
OxyLED T-01S Super Bright DIY Stick-on Anywhere 4-LED Touch Tap Light Push Light, LED Night Light OxyLED®- Natural Life, Natural Lights […] Posted in LED Lighting
8 Pack White Solar Power LED Lights Road Driveway Pathway Dock Path Ground Step This item is utilized high-quality LED […] Posted in Solar Dock Lights
Best undercabinet LSD lights on Amazon, and best customer service. I like the fact it is easily mountable w/o taking it apart (2 screws go all the way through the fully-assembled unit) and it can be direct-wired and mounted nearly flush against the back wall. Also the light is nicely diffuse–you can’t see individual LED cells. Exterior build-quality is also good with no rough edges or paint runs. I also like the fact the hole in the back for direct wiring is in the middle of the unit, so you can prewire the wall for the wire to come out in the middle of…
Great but expensive This replaced an under-cabinet florescent fixture. I was getting tired of replacing the florescent bulb every year or so. Someone noted in an earlier review that they couldn’t change the color or the brightness – both worked fine for me. But even at the lowest brightness setting, it is a LOT brighter than the florescent fixture it replaced.I knocked the unit down a star for two reasons: the expense – this is a very expensive fixture, and because the unit did not include any sort of…
OK light, time will tell how they hold up They seem like ok lights, only time will tell how they hold up since this company is only one year old. If you are replacing an older T5 undercounter light it will require extra work. The light is one inch thick and if you have romex coming through the wall you will have to hold the light down, I used 1/2″ rubber bumpers, I also used 2 inch self tappers to mount the light. I had to splice on a 14 gauge whip so I could enter the light, I cut off the slip connectors on the light…
Comments are disabled for this post.